|
FSP500-70AAPB is an industrial level of switching power supply. The power supply comes to offer the total power capacity up to 500 Watts, and uses unique active PFC (Power Factor Correction) circuit design with its high-load electrical components, makes it to be perfectly used in an industrial environment. In addition, with its full range of input and output electrical features, the power supply is ideally the best choice for server, workstation, communication or any other automation applications to use. The product also complies with the latest safety and EMC standards, which is perfectly to meet various regulations worldwide.
| Wattage |
500W |
| Dimension |
140mm (L) × 150 mm (W) × 86mm (H) |
| Product Highlight |
Efficiency Level |
80 Plus Platinum |
|
Altitude |
5000M |
|
PMBus |
For standard, advanced workstation, server and industrial power system. |
| General Specification |
Effciency |
85% 230VAC |
|
Voltage Regulation |
+3.3V, +12V, +5V, +5SB: ±5%
-12V, -5V: ±10% |
|
PWOK Delay Time |
500ms > PWOK > 100ms |
| Input Electrical Specification |
Input Frequency |
47 ~ 63 Hz |
|
Input Current |
115V@ 8.0 Amps-rms maximum
230V@ 4.0 Amps-rms maximum |
| Output Specification |
Hold-up time |
115V/60Hz 12mSec. Minimum@100% Load,
230V/50Hz 16mSec. Minimum@100% Load |
|
Ouput Voltage Regulation |
+3.3Vdc output : +3.5 Vdc minimum, + 4.8Vdc maximum
+5Vdc output : +5.5 Vdc minimum, + 7.0Vdc maximum
+12Vdc output : +13.4 Vdc minimum, + 16.0Vdc maximum
|
|
Ripple & Noise |
115V-rms/230V-rms 5V 20ms Maximum
|
|
Over current protection |
3.3V:50mV p-p
5V:50mV p-p
12V1:120mV p-p
12V2:120mV p-p
-12V:120mV p-p
5Vsb:50mV p-p
-5V:50mV p-p |
| Environmental Requirement |
Temperature Range |
Operating : 0 to +50℃
Storage :-20 to +80℃ |
|
Humidity |
Operating : 85% to % RH, Non-condensing
Storage : 95% to % RH, Non-condensing |
|
MBTF |
The power supply have a minimum predicted MTBF(MIL-HDBK-217) of 100,000 hours of continuous operation at 25℃, maximum-output load, and nominal AC inout voltage |
| Safety |
CE,FCC,TUV,UL/cUL |
Output Voltage and Current Rating
|
+3.3V |
+5V |
+12V1 |
+12V2 |
-12V |
-5V |
+5Vsb |
| Ripple-Noise(R-P) mV |
50mV |
50mV |
120mV |
120mV |
120mV |
50mV |
50mV |
| Regulation Load % |
±5% |
±5% |
±5% |
±5% |
±10% |
±10% |
±5% |
| Output Max.(A) |
24A |
20A |
18A |
18A |
0.5A |
0.2A |
3A |
| Output Min.(A) |
0.3A |
0.3A |
0.3A |
0.3A |
0A |
0A |
0A |
Notes
- The +3.3V and +5V total output shall not exceed 120watts.
- The total output for this subject power supply is 500 watts.
- Ripple and noise measurements shall be made under all specified load conditions through a single pole low pass filter with 20MHz cut off frequency. Outputs shall bypassed at the connector with a 0.1uF ceramic disk capacitor and a 47uF electrolytic capacitor to simulate system loading.
- -5V option.
|
